Understanding Essential Plumbing Skills is Essential for Bathtub Installation
Understanding Essential Plumbing Skills is Essential for Bathtub Installation
Blog Article
Just about everyone seems to have his or her own opinions in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bath tub isn't precisely brain surgery, however it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately challenging project. If the old bathtub is readily available, the task can relocate speedily; if you need to open up a wall to remove the old bathtub and also position the new bath tub, the task is much harder. In either instance, the project is within a residence handyman's abilities, although you will need an assistant to leave the old bathtub and embeded in the new one. See to it you have actually certified on your own for the job as well as are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed job, it is better to think about using one prior to you start. Chances are you may require an expert plumber to make tube connections.
This short article will certainly help you set up a brand-new tub in your shower room if you have currently purchased a new bathtub and also don't require to alter the arrangement of your previous water system pipelines.
Your devices as well as product checklist need to make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain pipes any water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin making certain that the washers remain in area between the faucet and the sink. Safeguard the faucet in position with the supplier given backnut. Once the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The previous kind ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Using both wooden boards under its feet, position the tub in the required setting. The wooden boards are useful in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub up until the level checks out degree.
To mount taps, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the same for the other faucet.
Activate the water supply and examine all joints and brand-new pipework for leaks as well as tighten them if required. Fill the bath tub as well as also inspect the overflow electrical outlet and also the typical outlet for leaks.
Lastly, fix the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait up until the bathtub has actually been utilized at least when as this will certainly settle it into its last placement.
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be suited its last setting.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, creating the water to penetrate the wall surface in between the bath and the tiling, causing problems with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components as well as installations. They are sold in tubes and also cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Remember to constantly load the bath tub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealer can crack relatively early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is a good idea to fit the tiles using waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very enthusiastic about Tools You Need to Install a New Bathtub and I really hope you enjoyed reading the new article. Make sure you take the opportunity to distribute this blog post if you enjoyed reading it. Thanks a lot for going through it.
Quality assured, call! Report this page